Table Blast Equipment

​

Performance and Production You Can Depend On

The most versatile type of blast cleaning equipment, Goff’s Table Blast models are ideal for large or heavy parts. Items to be cleaned are rotated on the table, exposing the parts to the abrasive blast. Single table, double-door swing and satellite multi-table models are available.

​

​

One Airless Blast Units

​

Wheel:

• The single direct drive blast wheel revolves at 3600 RPM for maximum abrasive velocity. 9” diameter wheel with 2” wide blades is standard. Balanced wheel components assure smooth operation.

​

Blades:

• Unique snap lock design eases blade replacement. Cast from abrasive resistant alloy to insure maximum life. Curved blade design provides maximum abrasive control.

​

Wheel Housing:

• The all welded low profile cabinet is fabricated from steel plate. Forklift slots provided for ease of movement.

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” steel plate.

Cabinet Liners:

• The cabinet is strategically lined with replaceable abrasive resistant steel and rubber liners.

​

Work Table:

 • 36” diameter work table is constructed of 3/8” steel plate.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 9 RPM.

​

Power Lock Doors:

 • The power lock for the door is electrically controlled with finger tip action. The pneumatically operated air cylinder provides locking action of the door. The rubber door seal prevents abrasive escape.

​

Blast Unit Mounting:

 • The unique mounting allows the blast unit to be pivoted, up to 15º to assure full coverage of parts to be cleaned. The blast unit is electrically oscillated with an adjustable timer. The pivoting action power is provided by a pneumatic cylinder.

​

Work Loading Height:

 • The unique mounting 32”

​

Maximum Work Dimensions:

 • 36” diameter or diagonal, 29” high.

​

Work Load Capacity:

 • 300 pounds.

​

Cabinet Access:

 • A lower access pan permits quick abrasive change.

​

​

Table Blast

​

FEATURES:

• Low Profile Design

• Safety Interlocks

• 300 Lb. Load Capacity

• Quick Cleaning Cycle

• Direct Drive Blast Wheel

• Abrasive Tight Cabinet

• Automatic Timer Controls

• Abrasive Resistant Liners

• Power Lock Door

• Oscillating Blast Wheel

• Machine Warranty

​

​

Specifications: 36 PTB Table Blast

             Equipment Dimensions

​

​

                             36PTB                  616DC

Width                      7' 1"                    included

Height                     7' 8"                       

Length                     5' 1"                      

Weight                   2,200 lbs.

​

Abrasive Recycling System

Screw Conveyors:

• A 4” diameter screw conveyor conveys the abrasive from the cabinet to the elevator.

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Bolt on doors permit service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provides positive belt adjustment.

​

Screening:

• Primary screen in cabinet protects screw conveyor from large objects. A secondary screen in storage hopper provides positive blast wheel protection. An additional screen in the abrasive funnel provides final protection to the blast wheel.

​

Abrasive Required:

• 275 pounds initial.

​

Abrasive Control:

• Fully adjustable butterfly valve provides precise flow control of abrasive.

Ventilation Features

​

500 CFM of dust collector is attached and is standard. Collector contains (6) cartridges which are automatically cleaned by an air pulse unit. Requires 80 to 110 PSI of air at 2 CFM.

​

Electrics

​

• NEMA type 12 electrical enclosure, thermal overload protection for all motors, optional single phase or three phase operation, 115 volt secondary control transformer, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls for blast wheel motor. Cycle alarm signal and hour meter standard. All motors are totally enclosed and fan cooled to provide maximum life. 

Full Load Amperes (excludes dust collector): 230V/3Ph/60Hz—12 Amps, 460V/3Ph/60Hz—6 Amps.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shut down, adjustable time delay allows flow of abrasive to brake blast wheel to a stop before door can be opened.

​

​

Noise Level: Approx 80 DB.

​

Airless Blast Unit

​

Wheel:

• The direct drive blast wheel revolves at 3600 RPM for maximum abrasive velocity. 12” diameter wheel with 8 curved blades 3” wide is standard. Balanced wheel components assure smooth operation.

​

Blades:

• Unique snap lock design eases blade replacement. Cast from abrasive resistant alloy to insure maximum life. Curved blade design provides maximum abrasive control.

Control Cage:

• Unique Dial type cage.

​

Wheel Housing:

• Fabricated from 1/4” wear resistant steel plate. Housing ends and top are lined with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” steel plate.

Cabinet Liners:

• Blast Chamber strategically rubber lined. Abrasive resistant steel liners are in line of direct blast.

​

Work Table:

 • 36” diameter work table is constructed of 3/8” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 9 RPM.

​

Power Lock Doors:

 • Electronically controlled pneumatically operated air cylinder provides locking action of door.

​

Work Loading Height:

 • 27”

​

Maximum Work Dimensions:

 • 36” diameter or diagonal, 22” high.

​

Work Load Capacity:

 • 1000 pounds.

​

​

Table Blast

​

​

FEATURES:

• Low Profile Design

• Safety Interlocks

• 1000 Lb. Load Capacity

• Quick Cleaning Cycle

• 7-1/2 HP Direct Drive Blast Wheel

• Abrasive Tight Cabinet

• Automatic Timer Controls

• Abrasive Resistant Liners

• Machine Warranty

​

Specifications: 36 TB Table Blast

             Equipment Dimensions

​

​

                             36TB                    816DC

Width                      3' 4"                     3' 10"

Height                     9' 3"                      6' 8"

Length                     4' 9"                     4' 5"

Weight                   2,200 lbs.              900 lbs.

Abrasive Recycling System

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Quick clamped removable cover permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 300 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator: 12” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

Ventilation Features

​

800 CFM of dust collection vacuum is required. Available optional collector contains 18, 4-1/2” diameter by 50” long polyester bags which are cleaned automatically by an air pulse unit. Requires 80 to 110 PSI of air at 2 CFM. 2 HP 3600RPM 230/460 volt/60/3 ph.

​

Electrics

​

• NEMA type 12 electrical enclosure, thermal overload protection for all motors, optional single phase or three phase operation, 115 volt secondary control transformer, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls both abrasive flow and blast wheel motor. Cycle alarm signal and hour meter standard.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. Automatic power shutdown if internal jamming occurs.

​

​

Noise Level: Approx 84 DB.

​

Airless Blast Unit

​

Wheel:

• The direct drive blast wheel is C-faced mounted and revolves at 3600 RPM for maximum abrasive velocity. The blast wheel is available in 12”, 13.5” and 15” diameters. Balanced wheel components assure smooth operation.

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

Control Cage:

• Unique Dial type cage.

​

Wheel Housing:

• Fabricated from 1/4” wear resistant steel plate. Housing ends and top are lined with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” steel plate.

Cabinet Liners:

• Blast Chamber strategically rubber lined. Abrasive resistant steel liners are in line of direct blast.

​

Work Table:

 • 48” diameter work table is constructed of 1/2” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 7 RPM.

​

Work Loading Height:

 • 34”

​

Maximum Work Dimensions:

 • 48” diameter or diagonal, 19” high at edge, 36” at center.

​

Work Load Capacity:

 • 5,000 pounds.

​

Cabinet Access:

 • Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.
 

Cabinet Door:

 • Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage. Rubber liner protects door from rebounding abrasive.

​

Table Blast

​

​

FEATURES:

• Automatic Timer Controls

• Safety Interlocks

• Machine Warranty

• Quick Cleaning Cycle

• 15 HP Direct Drive Blast Wheel

• Abrasive Tight Cabinet

• 5,000 Lb. Loads

• Abrasive Resistant Liners

​

Specifications: 48 TB S Table Blast

             Equipment Dimensions

​

​

                     48TB                    816DC               1850DC

Width             7' 3"                     3' 10"                   4' 2"

Height           10' 2"                     6' 8"                    7' 6"

Length            7' 4"                     4' 5"                    5' 10"

Weight          5,100 lbs.              700 lbs.                900 lbs

Abrasive Recycling System

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Quick clamped removable cover permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 400 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression

​

Separator: 12” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

Ventilation Features

​

800 CFM dust collector optional.

​

Electrics

​

• NEMA type 12 electrical enclosure, thermal overload protection for all motors, optional single phase or three phase operation, 115 volt secondary control transformer, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls for both abrasive and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheel before door can be opened.

​

​

Noise Level: Approx 84 DB.

​

Airless Blast Unit

​

Wheel:

• Two direct drive blast wheels revolve at 3600 RPM for maximum abrasive velocity. 9” diameter wheel with 4 curved blades 2” wide is standard. Balanced wheel components assure smooth operation.

​

Blades:

• Unique snap lock design eases blade replacement. Cast from abrasive resistant alloy to insure maximum life. Curved blade design provides maximum abrasive control.

Control Cage:

• Dial type cage.

​

Wheel Housing:

• Fabricated from 1/4” steel plate. Housing ends and top are lined with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” steel plate.

Cabinet Liners:

• Blast Chamber strategically rubber lined. Abrasive resistant steel liners are in line of direct blast.

​

Work Table:

 • 48” diameter work table is constructed of 3/8” steel plate table liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 6 RPM.

​

Work Loading Height:

 • 27 1/4”

​

Maximum Work Dimensions:

 • 48” diameter or diagonal, 38” to 40” in height.

​

Work Load Capacity:

 • 1,500 pounds.

​

Cabinet Access:

 • Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.

​

Cabinet Door:

 • Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage.

​

Table Blast

​

​

FEATURES:

• Automatic Timer Controls

• Safety Interlocks

• Machine Warranty

• Quick Cleaning Cycle

• Two 5 HP Direct Drive Blast Wheels

• Abrasive Tight Cabinet

• 1,500 Lb. Loads

• Abrasive Resistant Liners

​

Specifications: 48TB CS Table Blast

             Equipment Dimensions

​

​

                   48TB-CS                816DC                1850DC

Width             7' 3"                     3' 10"                   4' 2"

Height           11' 7/8"                  6' 8"                    7' 6"

Length            5' 2"                     4' 5"                    5' 10"

Weight          6,100 lbs.              700 lbs.                900 lbs

Abrasive Recycling System

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Quick clamped removable cover permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 400 to 500 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator: 9” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

Ventilation Features

​

850 CFM dust collector optional.

​

Electrics

​

• NEMA type 12 electrical enclosure, thermal overload protection for all motors, optional single phase or three phase operation, 115 volt secondary control transformer, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls for both abrasive and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheel before door can be opened.

​

​

Noise Level: Approx 84 DB.

​

Table Blast

​

​

FEATURES:

• Automatic Timer Controls

• Safety Interlocks

• Machine Warranty

• Quick Cleaning Cycle

• 15 HP Direct Drive Blast Wheel

• Abrasive Tight Cabinet

• 5,000 Lb. Loads

• Abrasive Resistant Liners

​

Specifications: 48 Table Blast w/Loop Elevator

Airless Blast Unit

​

Wheel:

• The direct drive blast wheel is C-faced mounted and revolves at 3600 RPM for maximum abrasive velocity. The blast wheel is available in 12”, 13.5” and 15” diameters. Balanced wheel components assure smooth operation.

​

Blades:

•Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” wear resistant steel plate. Housing is fully incased with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” steel plate.

Cabinet Liners:

• Blast Chamber strategically rubber lined. Abrasive resistant steel liners are in line of direct blast.

​

Work Table:

 • 48” diameter work table is constructed of 1/2” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 7 RPM.

​

Work Loading Height:

 • 34”

​

Maximum Work Dimensions:

 • 48” diameter or diagonal, 19” high at edge, 36” at center.

​

Work Load Capacity:

 • 5,000 pounds.

​

Cabinet Access:

 • Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.

​

Cabinet Door:

 • Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage. Rubber liner protects door from rebounding abrasive.

​

             Equipment Dimensions

​

​

                    48TBS                  816DC                1850DC

Width             7' 3"                     3' 10"                   4' 2"

Height           10' 2"                     6' 8"                    7' 6"

Length            7' 4"                     4' 5"                    5' 10"

Weight          5,100 lbs.              700 lbs.                900 lbs

Abrasive Recycling System

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Quick clamped removable cover permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 400 pounds initial

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator: 12” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

Ventilation Features

​

800 CFM dust collector optional.

​

Electrics

​

• NEMA type 12 electrical enclosure, thermal overload protection for all motors, optional single phase or three phase operation, 115 volt secondary control transformer, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls for both abrasive and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheel before door can be opened.

​

​

Noise Level: Approx 84 DB.

​

Table Blast

​

​

FEATURES:

• (1) 15 HP Blast Wheels

• 12” Gravity Lip Separator

• 5,000 Lb. Loads

• Abrasive Tight Cabinet

• Pitless Design

• Hip Mounted Blast Wheel

• Safety Interlocks

• Automatic Timer Controls

• Optional Auxiliary Wheel Available

• Machine Warranty

​

Specifications: 60TB-S Table Blast

Airless Blast Unit

​

Wheel:

• The direct drive blast wheel is C-faced mounted and revolves at 3600 RPM for maximum abrasive velocity. The blast wheel is available in 12”, 13.5” and 15” diameters. Balanced wheel components assure smooth operation.

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” steel plate. Housing ends and top are lined with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 3/8” steel plate. Opposing wall to blast wheels is 1/2” wear resistant steel plate.

​

Work Table:

 • 60” diameter work table is constructed of 3/8” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 4-1/2 RPM.

​

Work Loading Height:

 • 26”

​

Maximum Work Dimensions:

 • 60” diameter or diagonal, 31” high.

​

Work Load Capacity:

 • 5,000 pounds.

​

Cabinet Access:

 • Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.

​

Cabinet Door:

 • Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage. Rubber liner protects door from rebounding abrasive. 

Power Lock Door:

 • Electrically controlled, pneumatically operated air cylinder provides locking action of the door Labyrinth door seal prevents abrasive escape. Abrasive resistant liner protects door from abrasive rebound.

Blast Unit Mounting:

 • Unique mounting allows the blast unit to be pivoted up to 30º included angle to assure full coverage of all parts to be cleaned. Electronically controlled with adjustable timer, the pivoting action power is controlled by pneumatic cylinder.

​

             Equipment Dimensions

​

​

                    60TB                  1216DC               

Width             9' 2"                     2' 6"               

Height             14'                      5' 4"     

Length           7' 11"                   6' 1"                 

Weight          8,000 lbs.             1,200 lbs.          

Abrasive Recycling System

​

Screw Conveyors:

• Screw conveyors constructed with heavy duty 6” sectional flighting.

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Quick clamped removable cover permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment.

Screening:

• Primary screen in cabinet protects elevator from large objects. An optional perforated rotary screen between elevator and separator automatically removes small foreign objects from abrasive is available.

​

Abrasive Required:

• 2,000 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator: 

• Single 12” lip separator has adjustable abrasive spreader and adjustable refuse gate for thorough air washing of abrasive provides maximum contaminate removal.

Ventilation Features

​

Dust Collection (optional): 

• 1,370 CFM dust collector is fully self contained and is optional. Collector contains 8 cartridges which are cleaned automatically by a reverse pulse system. Requires 90-100 PSI of air at 7.5 SCFM. Free standing collector will accommodate 55 gallon refuse drum.

​

Electrics

​

• NEMA type 12 electrical enclosure, fusible disconnect switch, thermal overload protection on all motors, 230/460 volt primary, 115 volt secondary control transformer, blast wheel motor ammeters, oil tight push buttons, digital abrasive cycle timer. Timer controls both abrasive flow and blast wheel motor. Cycle alarm signal and hour meter standard.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheels to stop before door can be opened.

​

​

Noise Level: Approx 85 DB.

​

Table Blast

​

​

FEATURES:

• (2) 7-1/2 HP Blast Wheels

• 20” Gravity Lip Separator

• 5,000 Lb. Loads

• Abrasive Tight Cabinet

• Pitless Design

• Abrasive Resistant Steel Cabinet

• Safety Interlocks

• Oscillating Blast Wheels

• Machine Warranty

• Automatic Timer Controls

​

Specifications: 60TB-CS Table Blast

Airless Blast Unit

​

Wheel:

• The direct drive blast wheels are C-faced mounted and revolve at 3600 RPM for maximum abrasive velocity. The blast wheels are available in 12”, 13.5” and 15” diameters. Balanced wheel components assure smooth operation.

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” steel plate. Housing ends and top are lined with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/2” wear resistant steel plate. Opposing wall to blast wheels is 1/2” wear resistant steel plate.

​

Work Table:

 • 60” diameter work table is constructed of 3/8” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

​

Table Drive:

 • Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 4-1/2 RPM.

​

Work Loading Height:

 • 30-13/16”

​

Maximum Work Dimensions:

 • 60” diameter or diagonal, 52” high.

​

Work Load Capacity:

 • 5,000 pounds.

Power Lock Door:

 • Electrically controlled, pneumatically operated air cylinder provides locking action of the door Labyrinth door seal prevents abrasive escape. Abrasive resistant liner protects door from abrasive rebound.

Blast Unit Mounting:

 • Unique mounting allows the blast unit to be pivoted up to 20º included angle to assure full coverage of all parts to be cleaned. Electronically controlled with adjustable timer, the pivoting action power is controlled by pneumatic cylinder.

​

             Equipment Dimensions

​

​

                    60TB                  1216DC               

Width             9' 2"                     2' 6"               

Height             14'                      5' 4"     

Length           7' 11"                   6' 1"                 

Weight          8,700 lbs.             1,200 lbs.          

Abrasive Recycling System

​

Screw Conveyors:

• Screw conveyors constructed with heavy duty 6” sectional flighting.

​

Elevator:

• Centrifugal discharge belt and bucket elevator is dust tight. Quick clamped removable cover permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment.

Screening:

• Primary screen in cabinet protects elevator from large objects. An optional perforated rotary screen between elevator and separator automatically removes small foreign objects from abrasive is available.

​

Abrasive Required:

• 2,000 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator: 

• Single 20” lip separator has adjustable abrasive spreader and adjustable refuse gate for thorough air washing of abrasive provides maximum contaminate removal.

Ventilation Features

​

Dust Collection (optional): 

• 1,750 CFM dust collector is fully self contained and is optional. Collector contains 8 cartridges which are cleaned automatically by a reverse pulse system. Requires 90-100 PSI of air at 7.5 SCFM. Free standing collector will accommodate 55 gallon refuse drum.

​

Electrics

​

• NEMA type 12 electrical enclosure, fusible disconnect switch, thermal overload protection on all motors, 230/460 volt primary, 115 volt secondary control transformer, blast wheel motor ammeters, oil tight push buttons, digital abrasive cycle timer. Timer controls both abrasive flow and blast wheel motor. Cycle alarm signal and hour meter standard.

​

​

Safety Features 

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheels to stop before door can be opened.

​

​

Noise Level: Approx 85 DB.

​

Two Airless Blast Units

​

Wheels:

• (2) 20 HP direct drive blast wheel revolves at 3600 RPM for maximum abrasive velocity. 12” diameter wheel with 3” wide blades is standard. Balanced wheel components assure smooth operation. 3rd Blast Wheel Optional.

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” wear resistant steel plate. Housing is fully encased with cast interlocking wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type all welded structurally reinforced cabinet is fabricated from 1/4” and 3/8” steel plate. Full width front door. Interlocking door seals prevent abrasive escape. Abrasive resistant liner protects door and cabinet walls from direct or indirect abrasive blast

​

Door:

• All welded structurally reinforced doors are fabricated from 1/4” and 1/2” steel plate. Door is supported by a heavy-duty thrust bearing. Door is pivoted from a 3” diameter solid shaft surrounded by a 6” diameter steel pipe. Air cylinder powered cam lock is located on the door for positive sealing from abrasive and dust leakage.

​

Door Option:

• Door and table can be pivoted from right or left of cabinet. Two doors and tables are optionally available for increased production.

​

​

Table Construction 

​

Table:

 • Constructed of ¾” steel plate with abrasive resistant table liner. Table is attached to a network of 3/8” thick plates surrounded by a 72” diameter drive ring. Table rotates on solid shaft supported by heavy-duty thrust bearing.

​

Table Support:

 • The table support is constructed of 1/2” abrasive resistant steel plate welded to form a beam. The heavy-duty support is suspended from the cabinet door.

​

Table Drive:

 • Table is driven by an electric motor through a drive wheel. Drive mechanism is engaged with an air cylinder to assure continuous rotation of the table.

​

Table Speed:

 • Approx. 10 RPM

​

Work Loading Ht:

 • 38”

​

Maximum Work Dimensions:

 • 72” dia. x 52” high

​

Work Load Capacity:

 • 6,000 pounds maximum per table.

Table Blast

​

​

FEATURES:

• Two 20 HP Direct Drive Blast Wheels

• Pitless Design

• Double Swing Table Option

• Rotary Scalping Drum

• Dual 30” Lip Separator

• 6,000 Lb. Table Capacity

• Dual Heavy Duty Elevator System

• Safety Interlocks

• Machine Warranty

​

Specifications: 72 Swing Table

             Equipment Dimensions

​

​

                    72SW                  GCO 3-6               

Width              17'                         45"               

Height           15' 9"                      138"     

Length            10'                          62"                 

Weight          17,000 lbs.             1,395 lbs.          

Abrasive Recycling System

​

Screw Conveyors:

• Dual heavyduty screws in cabinet are chain and sprocket driven and protected by torque limiting clutch. Heavy-duty 9” screw from elevator to abrasive storage hopper. All screws have 2” shafting with exterior mounted bearings.

​

Elevator System:

• Heavy-duty centrifugal discharge belt and bucket elevator is rigid and dust tight. Screw adjusted take-ups provide positive belt alignment.

Separator:

• Double elevator design locates dual 30” lip separator at floor level. Dual separation provides thorough air washing of abrasive for maximum contaminate removal.

​

Screening:

• Heavy bar grating in cabinet protects screw conveyor from large objects. A screen between elevator and separator automatically removes small foreign debris.

​

Cabinet Ventilation:

• Air inlet and outlet positioned to provide maximum dust evacuation of cabinet.

​

Abrasive Required:

• 3,000 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive to both blast wheels. Totally enclosed design means maximum noise suppression.

​

​

Electrics

​

• NEMA type 12 electrical enclosure, fusible disconnect switch, thermal overload protection on all motors, 230/460 volt primary, 115 volt secondary control transformer, blast wheel motor ammeters, oil tight push buttons, digital cycle timer. Timer controls both abrasive flow and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard. Independent blast wheel operation. 

Full load amperes (excludes dust collector)

230V/3Ph/60Hz—115 Amps,

460V/3Ph/60Hz—58 Amps.

​

​

Ventilation Features

​

• (option) DFO 3-6 10 HP: 4300 CFM.

​

​

Noise Level: Approx 85 DB.

​

Airless Blast Unit

​

Wheel:

• (1) 20 HP direct drive blast wheel revolves at 3600 RPM for maximum abrasive velocity. 12” diameter wheel 3” wide blades is standard. Balanced wheel components assure smooth operation. (Option: Two wheel model available).

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” wear resistant steel plate. Housing is fully incased with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• ​Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” wear resistant steel plate. Built to withstand years of continuous usage.

​

Cabinet Liners:

• Blast chamber strategically lined with abrasive resistant steel. Interchangeable abrasive resistant liners are in line of direct blast.

​

Work Table:

• 72” diameter work table is constructed of 1/2” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

Table Drive:

• Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 7 RPM.

​

Work Loading Height:

• 38-1/2”

​

Maximum Work Dimensions:

• 72” diameter or diagonal, 30” high at edge and 43” at center

​

Work Load Capacity:

• 6,000 pounds.

​

Cabinet Access:

• Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.

​

Cabinet Door:

• Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage. Abrasive resistant liner protects door from abrasive rebound.

​

​

Table Blast

​

​

FEATURES:

• 20 HP Direct Drive Blast Wheel

• Single 20” Air Wash Separator

• 6,000 Lb. Loads

• Abrasive Tight Cabinet

• Optional 2nd Blast Wheel

• Abrasive Resistant Steel Cabinet

• Totally Enclosed Abrasive Valve

• Heavy Duty Elevator System

• Safety Interlocks 

• Automatic Timer Controls

• Machine Warranty

​

Specifications: 72 Swing Table

             Equipment Dimensions

​

​

                    72TB                  GCO 3-3               

Width            10' 4"                       25"               

Height           14' 1"                       96"     

Length           7' 11"                       65"                 

Weight          7,500 lbs.             1,275 lbs.          

Abrasive Recycling System

​

Screw Conveyors:

• Moves the abrasive from the bottom of the machine to the elevator using a heavy duty 9” screw flight supported by a 2” shaft.

​

Elevator:

• Centrifugal discharge belt and bucket elevator using 5” 2-ply heavy duty rubber belt and cast iron buckets. Quick clamped removable door permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment. Powered by 1-1/2 HP, 1800 RPM motor and reducer.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 3,000 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator:

• Single 20” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

​

​

Ventilation Features

​

• 2000 CFM dust collector is fully self contained. Contains 8 cartridges which are automatically cleaned by reverse air pulse system. Requires 90-100 PSI of air at 7.5 CFM. Free standing and accommodates a 55 gallon drum.

​

​

Electrics

​

• NEMA type 12 electrical enclosure, fusible disconnect switch, thermal overload protection on all motors, 230/460 volt primary, 115 volt secondary control transformer, blast wheel motor ammeters, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls both abrasive flow and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard. Full load Amperes (excludes dust collector): 230V/3Ph/60Hz—57 Amps, 460V/3Ph/60Hz—29 Amps.

​

​

Safety Features

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheels to stop before door can be opened.

​

​

Noise Level: Approx 85 DB.

​

Table Blast

​

​

FEATURES:

• 20 HP Direct Drive Blast Wheel

• Single 20” Air Wash Separator

• 6,000 Lb. Loads

• Abrasive Tight Cabinet

• Optional 2nd Blast Wheel

• Abrasive Resistant Steel Cabinet

• Totally Enclosed Abrasive Valve

• Heavy Duty Elevator System

• Safety Interlocks 

• Automatic Timer Controls

• Machine Warranty

​

Specifications: 72TB Table Blast

Airless Blast Unit

​

Wheel:

• (1) 20 HP direct drive blast wheel revolves at 3600 RPM for maximum abrasive velocity. 12” diameter wheel 3” wide blades is standard. Balanced wheel components assure smooth operation. (Option: Two wheel model available).

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” wear resistant steel plate. Housing is fully incased with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/4” wear resistant steel plate. Built to withstand years of continuous usage.

​

Cabinet Liners:

• Blast chamber strategically lined with abrasive resistant steel. Interchangeable abrasive resistant liners are in line of direct blast.

​

Work Table:

• 72” diameter work table is constructed of 1/2” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

Table Drive:

• Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 7 RPM.

​

Work Loading Height:

• 38-1/2”

​

Maximum Work Dimensions:

• 72” diameter or diagonal, 30” high at edge and 43” at center.

Work Load Capacity:

• 6,000 pounds.

​

Cabinet Access:

• Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.

​

Cabinet Door:

• Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage. Abrasive resistant liner protects door from abrasive rebound.

​

​

             Equipment Dimensions

​

​

                    72TB                  GCO 3-3               

Width            10' 4"                       25"               

Height           14' 1"                       96"     

Length           7' 11"                       65"                 

Weight          7,500 lbs.             1,275 lbs.          

Abrasive Recycling System

​

Screw Conveyors:

• Moves the abrasive from the bottom of the machine to the elevator using a heavy duty 9” screw flight supported by a 2” shaft.

​

Elevator:

• Centrifugal discharge belt and bucket elevator using 5” 2-ply heavy duty rubber belt and cast iron buckets. Quick clamped removable door permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment. Powered by 1-1/2 HP, 1800 RPM motor and reducer.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 3,000 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator:

• Single 20” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

​

​

Ventilation Features

​

• 2000 CFM dust collector is fully self contained. Contains 8 cartridges which are automatically cleaned by reverse air pulse system. Requires 90-100 PSI of air at 7.5 CFM. Free standing and accommodates a 55 gallon drum.

​

​

Electrics

​

• NEMA type 12 electrical enclosure, fusible disconnect switch, thermal overload protection on all motors, 230/460 volt primary, 115 volt secondary control transformer, blast wheel motor ammeters, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls both abrasive flow and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard. Full load Amperes (excludes dust collector): 230V/3Ph/60Hz—57 Amps, 460V/3Ph/60Hz—29 Amps.

​

​

Safety Features

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheels to stop before door can be opened.

​

​

Noise Level: Approx 85 DB.

​

Airless Blast Unit

​

Wheel:

• (2) 10 HP direct drive blast wheel revolves at 3600 RPM for maximum abrasive velocity. 12” diameter wheel 3” wide blades is standard. Balanced wheel components assure smooth operation.

​

Blades:

• Cast from abrasive resistant alloy to insure maximum life. The unique blade design allows for easy blade replacement.

​

Control Cage:

• Dial type cage. 

​

Wheel Housing:

• Fabricated from 1/4” steel plate. Housing is fully incased with replaceable wear resistant liners.

​

​

Cabinet Construction 

​

Cabinet:

• Pitless type, all welded structurally reinforced cabinet is fabricated from 1/2” wear resistant steel plate. Built to withstand years of continuous usage.

​

Work Table:

• 72” diameter work table is constructed of 1/2” steel plate with abrasive resistant liner standard. Cabinet configuration makes work table accessible by overhead hoist. Heavy duty table support bearings are completely enclosed for protection from stray abrasive.

Table Drive:

• Exterior mounted electric motor and gear reducer transmit power through special spring loaded rubber drive wheel. Table revolves at 7 RPM.

​

Work Loading Height:

• 30-3/4”

​

Maximum Work Dimensions:

• 72” diameter or diagonal, 45” at center.

​

Work Load Capacity:

• 5,000 pounds.

​

Cabinet Access:

• Lower access pan permits quick abrasive change. Clearance under abrasive reclaim system permits thorough cleanup.

​

Cabinet Door:

• Air cylinder powered cam lock door is positively sealed from abrasive and dust leakage. Abrasive resistant liner protects door from abrasive rebound.

​

Blast Unit Mounting:

• Unique mounting allows the blast unit to be pivoted up to 30° included angle to assure full coverage of all parts to be cleaned. Electronically controlled with adjustable timer, the pivoting action power is controlled by pneumatic cylinder.

​

Table Blast

​

​

FEATURES:

• 2-10 HP Direct Drive Blast Wheels

• Single 20” Air Wash Separator

• Oscillating Blast Wheels

• Abrasive Tight Cabinet 

• 5,000 Lb. Loads

• Abrasive Resistant Steel Cabinet

• Pitless Design

• Automatic Timer Controls

• Deep Notch Door for Table Center Loading

• Safety Interlocks

• Machine Warranty

​

Specifications: 72TB CS Table Blast

             Equipment Dimensions

​

​

                    72TB                  DFO 2-4               

Width            12' 8"                    3' 10"               

Height          14' 10"                     12'     

Length          7' 11"                     5' 5"                 

Weight          7,500 lbs.             1,275 lbs.          

Abrasive Recycling System

​

Screw Conveyors:

• Moves the abrasive from the bottom of the machine to the elevator using a heavy duty 9”screw flight supported by a 2” shaft.

​

Elevator:

• Centrifugal discharge belt and bucket elevator using 5” 2-ply heavy duty rubber belt and cast iron buckets. Quick clamped removable door permits service and inspection. All shaft bearings are exterior mounted for extended life. Screw adjusted take-up provide positive belt adjustment. Powered by 1-1/2 HP, 1800 RPM motor and reducer.

​

Screening:

• Primary screen in cabinet protects elevator from large objects. A secondary screen in storage hopper provides positive blast wheel protection.

​

Abrasive Required:

• 3,000 pounds initial.

​

Abrasive Control:

• Fully adjustable air actuated butterfly valve provides precise flow control of abrasive. Totally enclosed design means maximum noise suppression.

​

Separator:

• Single 20” gravity lip separator has adjustable abrasive spreader and adjustable refuse gate for maximum contaminate removal.

​

​

Ventilation Features

​

• 2000 CFM dust collector is fully self contained. Contains 8 cartridges which are automatically cleaned by reverse air pulse system. Requires 90-100 PSI of air at 7.5 CFM. Free standing and accommodates a 55 gallon drum.

​

​

Electrics

​

• NEMA type 12 electrical enclosure, fusible disconnect switch, thermal overload protection on all motors, 230/460 volt primary, 115 volt secondary control transformer, blast wheel motor ammeters, oil tight push buttons, 15 minute abrasive cycle timer. Timer controls both abrasive flow and blast wheel motor. Table jog switch to ease loading. Table lockout for blast pattern test. Cycle alarm signal and hour meter standard. Full load Amperes (excludes dust collector): 230V/3Ph/60Hz—57 Amps, 460V/3Ph/60Hz—29 Amps.

​

​

Safety Features

​

• Blast wheel operational only when door is closed. Door is locked closed electrically during blast cycle. After blast wheel shutdown, adjustable time delay allows flow of abrasive to brake blast wheels to stop before door can be opened.

​

​

Noise Level: Approx 85 DB.

​