Black Max Fans
Z Abrasives
Equipment & Repair
15606 CORNET STREET, SANTA FE SPRINGS, CA 90670
Call to place your order
(Phone) 1-714-330-3177
or (Fax) 562-404-4904

We believe in honesty, integrity and commitment to our customers.
Available 24hrs / 7 days a week / Same day shipping
Distributor of sandblasting equipment, spare parts and much more
GOFF Hydro Pulse
Goff Hydro Pulse HP2SPW
WATER BLAST DEGREASING & WASHING
FEATURES:
• Pneumatic Dump
• Gas Fired Heater
• Open Basket Tumble System
• No High Pressure Pumps
• Completely Self Contained Unit
• Auto Oil Skimmer
• 5 HP Direct Drive Water Wheel
• 150 Lb. Capacity
• Centrifugal Separator (optional)
Specifications: Hydro Pulse HP2SPW
Water Blast Unit
Wheel:
• One (1) 5 HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel with six openings 2” long x 3/4” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Work Handling System
The work handling system consists of a 24” diameter basket constructed of perforated plate with three blades at the bottom to provide gentle tumbling action insuring all parts are exposed to the cleaning pattern. A ring and pinion gear arrangement driven by a 1/3 HP motor mounted to a 60:1 reduction gear box rotates the basket at 5 RPM.
Capacity:
• 2 Cu. Ft., 150 lbs.
Cabinet Construction
Capacity:
• An all welded cabinet is fabricated of 1/4” steel plate. A large access door allows for ease for loading and unloading parts.
Pneumatic Dump:
• Two momentary push buttons located at the operator station, controls a pneumatic actuator to allow the basket to be rotated from run to dump positions or stopped anywhere between for inspection or loading.
Pumps:
• Vertical centrifugal sump pump is seal less and all cast iron constructed with direct coupled TEFC motors.
Equipment Dimensions
Width 4' 5"
Length 5' 1"
Height 7' 7"
Weight 2,500 lb.
Piping
Piping From Pump To Wheel:
• is schedule 40 steel with oil resistant, high temperature rubber hose at wheel connection. Hose allows for ease of maintenance and adjustments of blast pattern.
Tank Construction
Tank:
• Constructed of 1/4” steel plate formed and welded. Tank is insulated with 3/4” foam sheets and 14 gauge cover panel. Tank capacity is 150 gallons
Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offers high and low limits.. A pressure switch senses blower on. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Water Blast Unit
Wheel:
• One (1) 7-1/2 HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel with six openings 2” long x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Work Handling System
The work handling system is a uniquely designed flight and link arrangement. The link is cast iron with a stainless steel 9/16” pin and cotter pin. The flight is formed of 10 gauge plate. This design allows for a soft tumbling action, yet is strong, highly wear resistant and durable. Each flight is bolted to a link on each end with two stainless steel 3/8” bolts. Optional soft flights are compressed rubber over steel allowing a tight mill for extra small parts or cushioning for delicate parts.
Capacity:
• 3 Cu. Ft., 700 lbs.
Mill Speed:
• 11 feet per minute.
Mill Drive:
• Motor is direct coupled to a gear box mounted on the rear of the cabinet. The conveyor shaft is then driven by a chain and sprocket arrangement. For jam protection a shaft mounted torque limiting clutch is used.
Cabinet Construction
Cabinet:
• An all welded cabinet is fabricated of 1/4” steel plate. A large access door is located in the rear of the machine for conveyor replacement and access to interior parts of cabinet.
Power Door:
• Push button controls at operator station operate two 3-1/4” pneumatic cylinders. Door is lifted up and back for full access to mill area. Kick plates inside of door prevent parts from wedging between the door and mill.
Pumps:
• Vertical centrifugal sump pump is seal less and all cast iron constructed with direct coupled TEFC motors.
Goff Hydro Pulse HP3 Batch Tumbler
WATER BLAST DEGREASING & WASHING
FEATURES:
• Power Door
• Gas Fired Heater
• Unique Flight and Link Tumble System
• No High Pressure Pumps
• Completely Self Contained Unit
• Auto Oil Skimmer
• 7-1/2 HP Direct Drive Water Wheel
• Auto Drag System
• 700 LB. Capacity
• Self Cleaning Tank
Specifications: HP3
Equipment Dimensions
Width 5' 11'
Length 9'
Height 6' 11"
Piping
Piping From Pump To Wheel:
• is schedule 40 steel with oil resistant, high temperature rubber hose at wheel connection. Hose allows for ease of maintenance and adjustments of blast pattern.
Tank Construction
Tank:
• Constructed of 1/4” steel plate formed and welded. Tank is insulated with 3/4” foam sheets and 14 gauge cover panel. Tank capacity is 150 gallons
Drag Conveyor System:
• Constructed of ¼” steel with chain link and synthetic blades continually dragging the bottom of tank moving solids to the outside of the tank. The conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Separator System:
• (Optional) closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from hopper through a valve and into a waste container for easy disposal.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offers on and off limits. A pressure switch senses blower on. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Water Blast Unit
Wheel:
• Two 5 HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel with six openings 2” long x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Work Handling System
The work handling system is a uniquely designed flight and link arrangement. The link is cast iron with a stainless steel 9/16” pin and cotter pin. The flight is formed of 10 gauge plate. This design allows for a soft tumbling action, yet is strong, highly wear resistant and durable. Each flight is bolted to a link on each end with two stainless steel 3/8” bolts. Optional soft flights are compressed rubber over steel allowing a tight mill for extra small parts or cushioning for delicate parts.
Capacity:
• 6 Cu. Ft., 1000 lbs.
Mill Speed:
• 6 feet per minute.
Mill Drive:
• Motor is direct coupled to a gear box mounted on the rear of the cabinet. The conveyor shaft is then driven by a chain and sprocket arrangement. For jam protection a shaft mounted torque limiting clutch is used.
Cabinet Construction
Cabinet:
• An all welded cabinet is fabricated of 3/8” and 1/4” steel plate. A large access door is located in the rear of the machine for conveyor replacement and access to interior parts of cabinet.
Power Door:
• Push button controls at operator station operate two 4” pneumatic cylinders. Door is lifted up and back for full access to mill area. Kick plates inside of door prevent parts from wedging between the door and mill.
Goff Hydro Pulse HP6 Batch Tumbler
WATER BLAST DEGREASING & WASHING
FEATURES:
• Power Door
• Self Cleaning Tank
• Two 5 HP Direct Drive Water Wheels
• No High Pressure Pumps
• Unique Flight & Link Tumble System
• No Spray Nozzles
• Gas Fired Heater
• Remote Water Supply
• 1,000 LB. Capacity
Specifications: HP6
Equipment Dimensions
Width 7'
Length 6' 2"
Height 6' 10"
Weight 4,300 lb.
Return Pump and Screen:
• Water and dirt from washer is funneled into a basket where 1/8” or larger items are trapped. Basket is easily removed for cleaning. Water and fine dirt are returned to the supply by a flange mounted seal less sump pump. A high level limit switch is provided in case pump should fail. This switch will shut down main feed pump.
Remote Tank Construction
Tank:
• Constructed of 1/4” steel plate formed and welded. Tank is insulated with 3/4” foam sheets and 14 gauge cover panel. Tank capacity is 350 gallons
Pumps:
• Vertical centrifugal sump pump is seal less and all cast iron constructed with direct coupled T.E.F.C. motors.
Drag Conveyor System:
• Constructed of ¼” steel with chain link and synthetic blades continually dragging the bottom of tank moving solids to the outside of the tank. The conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Separator System:
• (Optional) closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from hopper through a valve and into a waste container for easy disposal.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offers on and off limits. A pressure switch senses blower on. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Water Blast Unit
Wheel:
• Two (2) 5 HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel with six openings 2” long x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Blast Chamber Construction
Work Handling:
• Three chambered drum constructed of stainless steel inner panels, steel top, bottom and outer panels.
Drum Drive:
• Exterior mounted C-face motor and gear reducer powers an HTD (High Torque Drive) for positive slip-proof indexing of the chamber drum.
Hook Spindle:
• Continual rotation of hook spindle during blasting operation provides full exposure of parts to the blast stream.
Hook Spindle Capacity:
• 100 lbs. per hook.
Hook Spindle Speed:
• 9 RPM.
Work Handling Capacity:
• Maximum area provided for material to be blasted is 13” diameter x 16” long..
Return Pump and Screen:
• Water and dirt from washer is funneled into a basket where 1/8” or larger items are trapped. Basket is easily removed for cleaning. Water and fine dirt are returned to the supply by a flange mounted seal less sump pump. A high level limit switch is provided in case pump should fail. This switch will shut down main feed pump.
Cabinet Construction
Cabinet:
• Constructed of 1/4” steel with 12 ga. Removable front panels sealed with neoprene for leak and noise control
Pumps:
• Vertical centrifugal sump pump is seal less and cast iron constructed with direct coupled T.E.F.C. motors.
Goff Hydro Pulse HP1316
WATER BLAST DEGREASING & WASHING
FEATURES:
• No Doors to Open & Close
• Two 5 HP Direct Drive Water Wheels
• No Waiting to Load or Unload
• Machine Warranty
• Continuous Production
• 100 Lb. Hook Capacity
• Gas Fired Heater
• No High Pressure Pumps
• Self Cleaning Tank
Specifications: HP1316
Equipment Dimensions
Width 6' 3"
Length 14' 2"
Height 7' 7"
Piping
Piping from Pump To Wheel:
• is schedule 40 steel with oil resistant, high temperature rubber hose at wheel connection. Hose allows for easy maintenance and pattern adjustments
Tank Construction
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 1” foam sheets and 16 gauge cover panel. Tank capacity is 250 gallons.
Drag Conveyor System:
• Constructed of 1/4” steel with chain link and synthetic blades continually dragging the bottom of tank move solids to the outside of the tank. The conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Heater Burner:
• Self ignition safety blower burner is used for water heating. A pressure switch senses blower on. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Burner is 300K BTU.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is very efficient with minimum heat loss.
Separator System (optional):
• is a closed loop design and is operated intermittently (time adjustable) to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from separator through a valve and into a waste container for easy disposal.
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• Motors are TEFC ball bearing 230/460 volts, 3 phase.
Water Blast Unit
Wheel:
• Two (2) 5 HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel with six openings 2” long x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Blast Chamber Construction
Work Handling:
• Three chambered drum constructed of stainless steel inner panels, steel top, bottom and outer panels.
Drum Drive:
• Exterior mounted C-face motor and gear reducer powers a chain and sprocket drive. Torque limiting is provided between drum shaft and final sprocket for jam protection. Adjustable stops on chamber top working in conjunction with automatic electrical switching provide variable indexing. Number of index stops variable from one to three per chamber.
Hook Spindle:
• Continual rotation of hook spindle during blasting operation provides full exposure of parts to the blast pattern.
Hook Spindle Capacity:
• 100 lbs. per hook.
Hook Spindle Speed:
• 9 RPM.
Work Handling System:
• Maximum area provided for material to be cleaned is 20” diameter x 38” long.
Cabinet Construction
Cabinet:
• Constructed of ¼” steel plate with 12 ga. Removable front panels sealed with neoprene for leak and noise control
Pumps:
• Vertical centrifugal sump pump is seal less and all cast iron constructed with direct coupled T.E.F.C.
Goff Hydro Pulse HP2038
WATER BLAST DEGREASING & WASHING
FEATURES:
• Continuous Production
• Detergent Optional
• Two 5 HP Direct Drive Water Wheels
• Machine Warranty
• Self Cleaning Tank
• No High Pressure Pumps
• Multiple Indexing
• No Spray Nozzles
• Gas Fired Heater
• No Doors to Open & Close
Specifications: HP2038
Equipment Dimensions
Width 7' 7"
Length 9' 8"
Height 8' 5"
Piping
Piping from Pump To Wheel:
• is schedule 40 steel with oil resistant, high temperature rubber hose at wheel connection. Hose allows for ease of maintenance and adjustments of blast pattern.
Tank Construction
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 1” foam sheets and 16 gauge cover panel. Tank capacity is 250 gallons.
Drag Conveyor System:
• Constructed of 1/4” steel with chain link and synthetic blades continually dragging the bottom of tank move solids to the outside of the tank. They conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offer main temperature control and high limit control. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Makeup water is automatically shut off when burner is turned off. Burner is 300K BTU
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is very efficient with minimum heat loss.
Separator System (optional):
• is a closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from separator through a valve and into a waste container for easy disposal.
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wipers depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Goff Hydro Pulse HP24
WATER BLAST DEGREASING & WASHING
FEATURES:
• Easy Load & Unload
• Lakos Separator
• 2 Ea. 7½ HP Water Wheels
• Offset Water Wheels
• Reversing Direct Drive Wheels
• Belt Oil Skimmer
• Eductor Circulated Water
• Turn Table Design
• 2000 Lb. Capacity
• Self Contained Water Reservoir
• Heavy Duty Design
Water Blast Unit
Wheel:
• Two (2) 7½ HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel and the wheels are mounted on a main frame as a stationary part of the machine. The wheels are canted, offset and stacked on the slopped end of the cabinet.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Cast of wear resistant alloy and adjustable for pattern control.
Shell (Cabinet) Construction
Shell:
• An all welded rolling shell is fabricated of 10 gauge steel setting on easy roll casters to allow for easy opening and closing of work chamber. Push button controls operate the door at the operators station. The door manually moves back for full access to cleaning area allowing loading and unloading from either side or from the top of the machine.
Work Handling System
Table:
• The 24” diameter work table is constructed of ¼” steel plate. The work table rides on four casters for a total load capacity of 2,000 lbs.
Table Drive:
• The exterior mounted electric motor and gear reducer are direct driven and transmit through a mechanical drive system allowing table to be lifted straight up for removal. The table revolves at five rotations per minute. Loading height of table is 23” off floor and completely exposed for easy loading and unloading.
Power Door Lock:
• The power door lock is electrically controlled with finger tip action. The pneumatically operated air cylinder provides locking action of the door.
Main Frame:
• Constructed of ¼” steel plate for an extra sturdy work handling system.
Piping
Lube Wheel:
• Manual lubrication for lubing all Delrin molecular bearings in table and cabinet shell casters.
Return Pump and Screen:
• Water and dirt from washer is funneled into a basket where 1/8” or larger items are trapped. Basket is easily removed for cleaning. Water and fine dirt are returned to the supply by a flange mounted seal less sump pump. A high level limit switch is provided in case pump should fail. This switch will shut down main feed pump.
Specifications: HP24
Equipment Dimensions
Width 5' 2"
Length 11' 4"
Height 7' 7"
Water Supply (Single Tank)
Tank:
• This self contained unit is the supply, heating and final filtering point for wash water.
Pumps:
• Vertical centrifugal sump pump is seal less and all cast iron constructed with direct coupled T.E.F.C.
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 1” foam sheets and 16 gauge cover panel.
Tank Capacity:
• 200 gallon
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offer main temperature control and high limit control. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Makeup water is automatically shut off when burner is turned off.
Fire Tube:
• A welded and pressure tested 5” tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Separator System (optional):
• is a closed loop design and is operated intermittently (time adjustable) to remove solids from tank area before they accumulate and generate erosion in the washer. A filter bag is installed below the separator to collect solids. Solids are removed from separator through a valve and into a bag for ease of disposal.
Oil Skimmer:
• Skimmer with a stainless steel belt powered by a 1/20 HP motor at 3 RPM. The belt is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Water Blast Unit
Wheel:
• Three water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel units are fabricated of stainless steel with six openings 2” long x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Blast Chamber Construction
Work Handling:
• Three chambered drum constructed of stainless steel inner panels, steel top, bottom and outer panels.
Drum Drive:
• Exterior mounted C-face motor and gear reducer powers a chain and sprocket drive. Torque limiting is provided between drum shaft and final sprocket for jam protection. Adjustable stops on chamber top working in conjunction with automatic electrical switching provide variable indexing. Number of index stops variable from one to three per chamber.
Hook Spindle:
• Continual rotation of hook spindle during blasting operation provides full exposure of parts to the blast pattern.
Hook Spindle Capacity:
• 100 lbs. per hook.
Hook Spindle Speed:
• 9 RPM
Work Handling System:
• Maximum area provided for material to be cleaned is 30” diameter x 38” long.
Cabinet Construction
Cabinet:
• Constructed of ¼” steel plate with 12 ga. Removable front panels sealed with neoprene for leak and noise control
Pumps:
• Vertical centrifugal sump pump is seal less and all cast iron constructed with direct coupled T.E.F.C
Goff Hydro Pulse HP3038
WATER BLAST DEGREASING & WASHING
FEATURES:
• Continuous Production
• Detergent Optional
• (3-4) 5 HP Direct Drive Water Wheels
• Machine Warranty
• Self Cleaning Tank
• No High Pressure Pumps
• Multiple Indexing
• No Spray Nozzles
• Gas Fired Heater
• No Doors to Open & Close
• 100 Lb. Hook Capacity
• No Waiting to Load or Unload
Specifications: HP3038
Equipment Dimensions
Width 8' 5"
Length 7' 11"
Height 9' 1"
Piping
Piping From Pump To Wheel:
• is schedule 40 steel with oil resistant, high temperature rubber hose at wheel connection. Hose allows for ease of maintenance and adjustments of blast pattern.
Tank Construction
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 1” foam sheets and 16 gauge cover panel. Tank capacity is 250 gallons.
Drag Conveyor:
• Constructed of 1/4” steel with chain link and synthetic blades continually dragging the bottom of tank move solids to the outside of the tank. They conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offer main temperature control and high limit control. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Makeup water is automatically shut off when burner is turned off. Burner is 300K BTU
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is very efficient with minimum heat loss.
Operational Separator System:
• is a closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from separator through a valve and into a waste container for easy disposal.
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wipers depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Goff Hydro Pulse HP36
WATER BLAST DEGREASING & WASHING
FEATURES:
• Easy Load & Unload
• 7-1/2 HP Water Wheel
• Stationary Main Frame
• Oscillating Wheel
• Gas Fired Heater
• 2000 Lb. Capacity
• Self Cleaning Tank
• No High Pressure Pumps
Specifications: HP36
Equipment Dimensions
Width 5'
Length 11'
Height 5' 8"
Water Blast Unit
Wheel:
• One (1) 7½ HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel unit is fabricated of stainless steel with six openings 2” x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Shell (Cabinet) Construction
Shell:
• An all welded rolling shell is fabricated of 10 gauge steel setting on easy roll casters to allow for easy opening and closing of work chamber.
Work Handling System
Table:
• The 36” diameter work table is constructed of ¼” steel plate. The work table rides on four casters for a total load capacity of 2,000 lbs.
Table Drive:
• The exterior mounted electric motor and gear reducer are direct driven and transmit through a mechanical drive system allowing table to be lifted straight up for removal. The table revolves at five rotations per minute. Loading height of table is 23” off floor and completely exposed for easy loading and unloading.
Power Door Lock:
• The power door lock is electrically controlled with finger tip action. The pneumatically operated air cylinder provides locking action of the door.
Main Frame:
• Constructed of ¼” steel plate for an extra sturdy work handling system.
Lube System:
• Manual lubrication system has been mounted for easy lubing of all Delrin High Molecular bearings in table and cabinet shell casters.
Return Pump and Screen:
• Water and dirt from washer is funneled into a basket where 1/8” or larger items are trapped. Basket is easily removed for cleaning. Water and fine dirt are returned to the supply by a flange mounted seal less sump pump. A high level limit switch is provided in case pump should fail. This switch will shut down main feed pump.
Capacity:
• 36” dia. x 33” high, 2,000 lbs.
Remote Tank Construction:
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 3/4” foam sheets and 16 gauge cover panel. Tank capacity is 350 gallons.
Drag Conveyor System:
• Constructed of 1/4” steel with chain link and synthetic blades continually dragging the bottom of tank moving solids to the outside of the tank. The conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offer main temperature control and high limit control. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Makeup water is automatically shut off when burner is turned off.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Separator System (operational):
• is a closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from hopper through a valve and into a waste container for easy disposal.
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Goff Hydro Pulse HP48
WATER BLAST DEGREASING & WASHING
FEATURES:
• Easy Load & Unload
• 7-1/2 HP Water Wheel
• Stationary Main Frame
• Oscillating Wheel
• Gas Fired Heater
• 2000 Lb. Capacity
• Self Cleaning Tank
• No High Pressure Pumps
Specifications: HP48
Equipment Dimensions
Width 7' 4"
Length 14"
Height 10' 11"
Water Blast Unit
Wheel:
• Three (3) 5 HP water wheel units (Standard). The direct drive water wheel rotates at 1750 RPM for maximum water velocity. 14” diameter wheel unit is fabricated of stainless steel with six openings 2” x 1” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Shell (Cabinet) Construction
Shell:
• An all welded rolling shell is fabricated of 10 gauge steel setting on easy roll casters to allow for easy opening and closing of work chamber.
Work Handling System
Table:
• The 48” diameter work table is constructed of ¼” steel plate. The work table rides on four casters for a total load capacity of 2,000 lbs.
Table Drive:
• The exterior mounted electric motor and gear reducer are direct driven and transmit through a mechanical drive system allowing table to be lifted straight up for removal. The table revolves at five rotations per minute. Loading height of table is 23” off floor and completely exposed for easy loading and unloading.
Power Door Lock:
• The power door lock is electrically controlled with finger tip action. The pneumatically operated air cylinder provides locking action of the door.
Main Frame:
• Constructed of ¼” steel plate for an extra sturdy work handling system.
Lube System:
• Manual lubrication system has been mounted for easy lubing of all Delrin High Molecular bearings in table and cabinet shell casters.
Return Pump and Screen:
• Water and dirt from washer is funneled into a basket where 1/8” or larger items are trapped. Basket is easily removed for cleaning. Water and fine dirt are returned to the supply by a flange mounted seal less sump pump. A high level limit switch is provided in case pump should fail. This switch will shut down main feed pump.
Capacity:
• 48” dia. x 48” high, 2,000 lbs.
Remote Tank Construction
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 3/4” foam sheets and 14 gauge cover panel. Tank capacity is 300 gallons.
Drag Conveyor System:
• Constructed of 1/4” steel with chain link and synthetic blades continually dragging the bottom of tank moving solids to the outside of the tank. The conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offer main temperature control and high limit control. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Makeup water is automatically shut off when burner is turned off.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Separator System (operational):
• is a closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from hopper through a valve and into a waste container for easy disposal.
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.
Goff Hydro Pulse HP60SCT
WATER BLAST DEGREASING & WASHING
FEATURES:
• Easy Load & Unload
• 7-1/2 HP Water Wheel
• Stationary Main Frame
• Heavy Duty Construction
• Oscillating Wheel
• Gas Fired Heater
• 3000 Lb. Capacity
• No High Pressure Pumps
• Self Cleaning Tank
Specifications: HP60SCT
Water Blast Unit
Wheel:
• Two (1) 7½ HP water wheel units (Standard). The direct drive water wheel units rotate at 1750 RPM for maximum water velocity. 14” diameter wheel unit is fabricated of stainless steel with six openings 1-3/4” x 3/4” wide.
Wheel Housing:
• Fabricated from ¼” steel plate.
Control Nozzle:
• Adjustable for pattern control to direct cleaning areas.
Shell (Cabinet) Construction
Shell:
• An all welded rolling shell is fabricated of 10 gauge steel setting on easy roll casters to allow for easy opening and closing of work chamber.
Work Handling System
Table:
• The 60” diameter work table is constructed of ¼” steel plate. The work table rides on four casters for a total load capacity of 3,000 lbs.
Table Drive:
• The exterior mounted electric motor and gear reducer are direct driven and transmit through a mechanical drive system allowing table to be lifted straight up for removal. The table revolves at five rotations per minute. Loading height of table is 30” off floor and completely exposed for easy loading and unloading.
Power Door Lock:
• The power door lock is electrically controlled with finger tip action. The pneumatically operated air cylinder provides locking action of the door.
Main Frame:
• Constructed of ¼” steel plate for an extra sturdy work handling system.
Lube System:
• Manual lubrication system has been mounted for easy lubing of all Delrin High Molecular bearings in table and cabinet shell casters.
Equipment Dimensions
Width 5'
Length 11"
Height 5' 8"
Return Pump and Screen:
• Water and dirt from washer is funneled into a basket where 1/8” or larger items are trapped. Basket is easily removed for cleaning. Water and fine dirt are returned to the supply by a flange mounted seal less sump pump. A high level limit switch is provided in case pump should fail. This switch will shut down main feed pump.
Capacity:
• 60” dia. x 46” high, 3,000 lbs.
Remote Tank Construction
Tank:
• Constructed of ¼” steel plate formed and welded. No bottom drains insure against accidental spills and improper discharge of tank contents. The tank is insulated with 3/4” foam sheets and 14 gauge cover panel. Tank capacity is 300 gallons.
Drag Conveyor System:
• Constructed of 1/4” steel with chain link and synthetic blades continually dragging the bottom of tank moving solids to the outside of the tank. The conveyor is driven by a 1/3 HP motor moving at approximately 2-1/2 feet per minute.
Heater Burner:
• A self ignition safety blower burner is used for water heating. Twin thermostat controls offer main temperature control and high limit control. Gas pressure and pilot light are monitored before main gas valve is opened for burner ignition. Makeup water is automatically shut off when burner is turned off.
Fire Tube:
• A welded and pressure tested tube channels and transfers heat to water within the tank. System is efficient with minimum heat loss.
Burner:
• 300,000 BTU
Separator System (operational):
• is a closed loop design and is operated continuously to remove solids from tank area before they accumulate and generate erosion in the washer. A waste hopper is installed below the separator to collect solids. Solids are removed from hopper through a valve and into a waste container for easy disposal.
Oil Skimmer:
• Fabricated from 1/4” steel with 14” skimmer wheel direct driven by a 1/20 HP motor at 2 RPM. The wheel is continually wiped clean with synthetic wiper depositing the oils and lights in a separate container for disposal.
Electric Motors
• All motors are TEFC ball bearing 230/460 volts, 3 phase.